Kanguru miniClone 1HD SATAUser GuideCopyright 2009, All Rights Reserved.
103.2 Connecting Bare Hard DrivesConnecting 3.5” HDDsHold the HDD vertically with the SATA connector at the bottom-left and then slowly insert it int
113.3 Removing Bare Hard DrivesTo remove a bare hard drive, push the eject button to the left of the bare HDD that you want to remove. This will caus
123.4 Connecting External Hard DrivesThe Disk 3 and Disk 4 ports are USB / eSATA combo ports. Both USB and eSATA external hard drives or flash drives
134. Operating Your Kanguru miniCloneThings to remember• Make sure that sufficient power is supplied to the Kanguru miniClone. Incorrect power wil
144.1 The User InterfaceKanguru Solutions designed the Kanguru miniClone’s menu system with the professional in mind. The menu system is fast, re
154.2 General OperationPlease follow these steps to execute the miniClone’s main functions (Copy, Compare, Erase, Seek):1. Connect the AC adaptor an
165. Select the hard drive by pressing the Up or Down directional button. Press the ENTER button to confirm your selection. 12Disk CopySource DiskD
174.3 Pausing and Cancelling a ProcessIf you wish to pause the current process, press the ENTER button. Press the ENTER button again to resume.If you
184.4 Information Reporting While a function is in progress, real time information is provided to you. Information can be displayed in two modes: Det
195. Menu and Functions• Device • Copy ○ Disk Copy ○ Disk Copy & Compare ○ Partition Copy ○ Partition Copy & Compare• Compare ○ Disk
2NOTICES AND INFORMATIONPlease be aware of the following points before using your Kanguru miniCloneCopyright© 2009, Kanguru Solutions. All rights rese
205.1 DeviceDevice mode allows you to connect any one drive to a PC so that it can be used like an external HDD. To connect a hard drive attached to
215.1.1 Connecting a DeviceTo connect a hard drive to your PC via the miniClone:1. Connect the miniClone to your PC via the eSATA or USB port on the
225.1.2 Disconnecting a DeviceTo disconnect a device connected to your PC via the miniClone:1. Press the ENTER button. The unplug device menu appears
235.2 CopyCopy mode allows you to copy data from a Source Drive to a Destination Drive. • The Source Drive needs to be attached to either the Disk 1
245.2.2 Disk Copy & CompareDisk Copy & Compare copies all data from the Source Drive to the Destination Drive. Once the copy process is comple
255.2.3 Partition Copy If you have a Source Disk with unallocated space on it, Partition Copy allows you to duplicate only primary and extended partit
265.2.4 Partition Copy & Compare Partition Copy & Compare copies all primary and extended partitions on the Source Drive to the
275.3 CompareCompare mode checks the contents of two hard drives to make sure that the data on both drives are the same. There are two Compare functi
285.3.2 Partition ComparePartition Compare checks the contents of any primary or extended partitions on two hard drives to make sure that the data on
295.4 EraseErase mode allows you to erase data on a connected hard drive. The hard drive needs to be attached to either Disk 2 or Disk 4. There are
3Table of ContentsTable of ContentsNotices and Information ...
305.4.2 Full EraseFull Erase deletes all data and file systems on the hard drive by writing “00” into all of the sectors. After a Full Erase, any data
315.4.4 7 x Wipe7 x Wipe deletes all data and file systems on the hard drive by alternatively writing hexadecimals “00” and “FF” into all of the secto
325.5 CheckCheck mode allows you to run several diagnostic functions that can run status reports on your hard drives. There are three Check
335.5.3 Seek TestSeek Test performs a full-stroked seek test on a hard drive. The Seek Test checks the hard drive’s physical status to make sure that
345.6 OptionThe Option menu provides you with option items that allow you to configure how your Kanguru miniClone operates. There are
355.6.1 General Option From the Option menu:1. Select General Option and then press the ENTER button. This will bring up the General Option menu. 2.
365.6.2 Temperature OptionFrom the Option menu:1. Select Temperature Option and then press the ENTER button. This will bring up the Temperature Optio
375.6.3 Error OptionFrom the Option menu:1. Select Error Option and then press the ENTER button. This will bring up the Error Option menu. 2. Press
385.6.4 Buzzer OptionFrom the Option menu:1. Select Buzzer Option and then press the ENTER button. This will bring up the Buzzer Option menu. 2. P
395.6.5 Display OptionFrom the Option menu:1. Select Display Option and then press the ENTER button. This will bring up the Display Option menu. 2.
45.4 Erase ... 295.4.1 Quick Erase ...
405.6.6 InformationThe Information item displays the miniClone’s version, serial number and firmware. The information displayed here is not configurab
416. Error and Warning Messages DefinedThe following chapter describes the most common error messages that you may encounter while using your Kangu
426.2 Initialization WarningsIf there is are any issues that the miniClone recognizes during the initialization process, the warning message will be
436.3 Process ErrorsIf an error occurs during a process, the error will be displayed as follows and the process will be stopped:The
446.4 Retry ErrorsIf an error occurs and the miniClone retries the process, it can be displayed as follows:Disk CopyDisk1 Disk2Disk2 R=rrRD:xxxxxxx
457. TroubleshootingPlease check the followings if you are experiencing unusual behavior by your Kanguru miniClone.Problem Possible SolutionHard dr
468. FAQQ : Is it possible to copy data between 2 HDDs with different capacities?A : It is possible. If the capacity of the Destination Disk is lar
47Q : The capacity of the Destination Disk is smaller than the Source Disk, but the total amount of data on the Source Disk is equal to or less than t
489. WarrantyThis product carries a 1 year* warranty. Kanguru Solutions is not responsible for any damages incurred in the shipping process. Any
Legal terms and conditions available at www.kanguru.com. Please review and agree before use. Thank you.Kanguru Solutions 1360 Main StreetMillis, MA 02
5Introduction1. IntroductionCongratulations on your purchase of the Kanguru miniClone from Kanguru Solutions. The Kanguru miniClone is a high speed
61.1 Package ContentsIf any of the following items are missing, please call Kanguru Solutions’ Tech Support department at: (508) 376-4245, extension
72. Parts and FunctionsFront View OLED DisplayDisk 3 Port(USB 2.0 / eSATA)Disk 4 Port(USB 2.0 / eSATA)4 Direction Cursor SpeakerPOWER / ENTE
83. Connecting and Removing Hard DrivesThere are 4 ports for connecting hard drives to your miniClone. The Disk 1 and Disk 2 ports on the top of th
93.1 Where to Connect Hard DrivesIt is important when connecting a hard drive that you are aware which position you are connecting your hard drive to
Kommentare zu diesen Handbüchern